17/30326671 DC : 0
NA
Status of Standard is Unknown
BS ISO 27919-1 - CARBON DIOXIDE CAPTURE - PART 1: PERFORMANCE EVALUATION METHODS FOR POST-COMBUSTION CO[2] CAPTURE INTEGRATED WITH A POWER PLANT
Hardcopy , PDF
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms, definitions and symbols
4 Defining the system boundary
5 Definition of basic PCC plant performance
6 Definition of utilities and consumption calculation
7 Guiding principle - Basis for PCC plant performance
assessment
8 Instruments and measurement methods
9 Evaluation of key performance indicators
Annex A - Test principles and guidelines
Annex B - Instruments and measurement methods
Annex C - Additional approaches of performance evaluation
for a PCC plant integrated with a power plant
Annex E - Standard reference conditions
Annex F - Check list for performance evaluation
Bibliography
BS ISO 27919-1.
Committee |
PSE/265
|
DocumentType |
Draft
|
Pages |
81
|
PublisherName |
British Standards Institution
|
Status |
NA
|
Supersedes |
ISO/TR 15377:2007 | Measurement of fluid flow by means of pressure-differential devices Guidelines for the specification of orifice plates, nozzles and Venturi tubes beyond the scope of ISO 5167 |
ISO 5167-3:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 3: Nozzles and Venturi nozzles |
ISO/IEC 17025:2005 | General requirements for the competence of testing and calibration laboratories |
IEC 60044-7:1999 | Instrument transformers - Part 7: Electronic voltage transformers |
ISO 10795:2011 | Space systems Programme management and quality Vocabulary |
IEC 61869-3:2011 | Instrument transformers - Part 3: Additional requirements for inductive voltage transformers |
ISO 6974-6:2002 | Natural gas Determination of composition with defined uncertainty by gas chromatography Part 6: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and C1 to C8 hydrocarbons using three capillary columns |
ISO 6327:1981 | Gas analysis — Determination of the water dew point of natural gas — Cooled surface condensation hygrometers |
ISO 5168:2005 | Measurement of fluid flow — Procedures for the evaluation of uncertainties |
IEC 60044-8:2002 | Instrument transformers - Part 8: Electronic current transformers |
ISO 6974-2:2012 | Natural gas — Determination of composition and associated uncertainty by gas chromatography — Part 2: Uncertainty calculations |
ISO 12242:2012 | Measurement of fluid flow in closed conduits Ultrasonic transit-time meters for liquid |
ISO 6974-4:2000 | Natural gas — Determination of composition with defined uncertainty by gas chromatography — Part 4: Determination of nitrogen, carbon dioxide and C1 to C5 and C6+ hydrocarbons for a laboratory and on-line measuring system using two columns |
IEC 61869-2:2012 | Instrument transformers - Part 2: Additional requirements for current transformers |
ISO/IEC Guide 98-1:2009 | Uncertainty of measurement — Part 1: Introduction to the expression of uncertainty in measurement |
ISO/TR 16344:2012 | Energy performance of buildings Common terms, definitions and symbols for the overall energy performance rating and certification |
ISO 15713:2006 | Stationary source emissions Sampling and determination of gaseous fluoride content |
ISO 7935:1992 | Stationary source emissions — Determination of the mass concentration of sulfur dioxide — Performance characteristics of automated measuring methods |
ISO 5167-4:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 4: Venturi tubes |
ISO 6974-3:2000 | Natural gas Determination of composition with defined uncertainty by gas chromatography Part 3: Determination of hydrogen, helium, oxygen, nitrogen, carbon dioxide and hydrocarbons up to C8 using two packed columns |
ISO 25597:2013 | Stationary source emissions Test method for determining PM2,5 and PM10 mass in stack gases using cyclone samplers and sample dilution |
ISO/IEC Guide 99:2007 | International vocabulary of metrology Basic and general concepts and associated terms (VIM) |
ISO 5167-2:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 2: Orifice plates |
IEC 60953-1:1990 | Rules for steam turbine thermal acceptance tests. Part 1: Method A - High accuracy for large condensing steam turbines |
ISO 5167-5:2016 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full — Part 5: Cone meters |
ISO 12039:2001 | Stationary source emissions Determination of the mass concentration of carbon monoxide, carbon dioxide and oxygen in flue gas Performance characteristics of automated measuring systems |
ISO 1213-1:1993 | Solid mineral fuels Vocabulary Part 1: Terms relating to coal preparation |
EN 1911:2010 | Stationary source emissions - Determination of mass concentration of gaseous chlorides expressed as HCl - Standard reference method |
ISO 13443:1996 | Natural gas Standard reference conditions |
ISO/TR 9464:2008 | Guidelines for the use of ISO 5167:2003 |
ISO 27913:2016 | Carbon dioxide capture, transportation and geological storage Pipeline transportation systems |
ISO 5167-1:2003 | Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements |
BS 7405:1991 | Guide to selection and application of flowmeters for the measurement of fluid flow in closed conduits |
ISO 14164:1999 | Stationary source emissions — Determination of the volume flowrate of gas streams in ducts — Automated method |
IEC 60953-2:1990 | Rules for steam turbine thermal acceptance tests. Part 2: Method B - Wide range of accuracy for various types and sizes of turbines |
IEC 61869-5:2011 | Instrument transformers - Part 5: Additional requirements for capacitor voltage transformers |
ISO 6974-1:2012 | Natural gas — Determination of composition and associated uncertainty by gas chromatography — Part 1: General guidelines and calculation of composition |
IEC 60953-3:2001 | Rules for steam turbine thermal acceptance tests - Part 3: Thermal performance verification tests of retrofitted steam turbines |
ISO 10849:1996 | Stationary source emissions — Determination of the mass concentration of nitrogen oxides — Performance characteristics of automated measuring systems |
ISO 17089-1:2010 | Measurement of fluid flow in closed conduits - Ultrasonic meters for gas Part 1: Meters for custody transfer and allocation measurement |
ISO 10780:1994 | Stationary source emissions — Measurement of velocity and volume flowrate of gas streams in ducts |
ISO 17179:2016 | Stationary source emissions — Determination of the mass concentration of ammonia in flue gas — Performance characteristics of automated measuring systems |
ISO 2186:2007 | Fluid flow in closed conduits — Connections for pressure signal transmissions between primary and secondary elements |
ISO/TR 27912:2016 | Carbon dioxide capture Carbon dioxide capture systems, technologies and processes |
ISO 3966:2008 | Measurement of fluid flow in closed conduits Velocity area method using Pitot static tubes |
ISO 10396:2007 | Stationary source emissions — Sampling for the automated determination of gas emission concentrations for permanently-installed monitoring systems |
ISO 6974-5:2014 | Natural gas Determination of composition and associated uncertainty by gas chromatography Part 5: Isothermal method for nitrogen, carbon dioxide, C1 to C5 hydrocarbons and C6+ hydrocarbons |
ISO 17089-2:2012 | Measurement of fluid flow in closed conduits - Ultrasonic meters for gas — Part 2: Meters for industrial applications |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.