I.S. EN ISO 23553-1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
SAFETY AND CONTROL DEVICES FOR OIL BURNERS AND OIL-BURNING APPLIANCES - PARTICULAR REQUIREMENTS - PART 1: AUTOMATIC AND SEMI-AUTOMATIC VALVES (ISO 23553-1:2014)
Hardcopy , PDF
01-04-2022
English
01-01-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Test conditions
6 Construction
7 Performance
8 EMC/Electrical requirements
9 Marking, installation and operating instructions
Annex A (informative) - Leak-tightness test - Volumetric
method
Annex B (informative) - Leak-tightness test - Pressure-loss
method
Annex C (normative) - Conversion of pressure loss into
leakage rate
Annex D (normative) - Test for immunity to power-frequency
magnetic fields
Annex E (normative) - Specific regional requirements in
European countries
Annex F (normative) - Specific regional requirements in
Canada and USA
Annex G (normative) - Specific regional requirements in Japan
Bibliography
Describes safety, constructional and performance requirements and testing of automatic and semi-automatic valves for oil.
DevelopmentNote |
Supersedes I.S. EN 264. (08/2009)
|
DocumentType |
Standard
|
Pages |
52
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
ISO 23553-1:2014 | Identical |
EN ISO 23553-1:2014 | Identical |
ISO 272:1982 | Fasteners — Hexagon products — Widths across flats |
EN 1254-3:1998 | Copper and copper alloys - Plumbing fittings - Part 3: Fittings with compression ends for use with plastics pipes |
ISO 1179-1:2013 | Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing — Part 1: Threaded ports |
ISO 3601-5:2015 | Fluid power systems O-rings Part 5: Specification of elastomeric materials for industrial applications |
EN 1591-1:2013 | Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation |
ISO 8434-1:2007 | Metallic tube connections for fluid power and general use Part 1: 24 degree cone connectors |
UL 50:13ED 2015-10 | Enclosures for Electrical Equipment, Non-Environmental Considerations |
EN 10226-2:2005 | Pipe threads where pressure tight joints are made on the threads - Part 2: Taper external threads and taper internal threads - Dimensions, tolerances and designation |
IEC 60730-2-19:1997+AMD1:2000+AMD2:2007 CSV | Automatic electrical controls for household and similar use - Part 2-19: Particular requirements for electrically operated oil valves, including mechanical requirements |
EN 10305-3:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 3: Welded cold sized tubes |
EN 1254-5:1998 | Copper and copper alloys - Plumbing fittings - Part 5: Fittings with short ends for capillary brazing to copper tubes |
EN 1057:2006+A1:2010 | Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications |
EN 10305-6:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 6: Welded cold drawn tubes for hydraulic and pneumatic power systems |
EN 1254-1:1998 | Copper and copper alloys - Plumbing fittings - Part 1: Fittings with ends for capillary soldering or capillary brazing to copper tubes |
EN 1254-2:1998 | Copper and copper alloys - Plumbing fittings - Part 2: Fittings with compression ends for use with copper tubes |
ISO/TR 7620:2005 | Rubber materials — Chemical resistance |
EN 1092-3:2003/AC:2007 | FLANGES AND THEIR JOINTS - CIRCULAR FLANGES FOR PIPES, VALVES, FITTINGS AND ACCESSORIES, PN DESIGNATED - PART 3: COPPER ALLOY FLANGES |
ISO 23936-1:2009 | Petroleum, petrochemical and natural gas industries — Non-metallic materials in contact with media related to oil and gas production — Part 1: Thermoplastics |
PREN 12514-4 : DRAFT 2009 | PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES |
ISO 9974-1:1996 | Connections for general use and fluid power Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports |
ISO 8216-99:2002 | Petroleum products Fuels (class F) Classification Part 99: General |
ISO 9974-3:1996 | Connections for general use and fluid power — Ports and stud ends with ISO 261 threads with elastomeric or metal-to-metal sealing — Part 3: Stud ends with metal-to-metal sealing (type B) |
ISO 8217:2017 | Petroleum products — Fuels (class F) — Specifications of marine fuels |
EN 10305-2:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 2: Welded cold drawn tubes |
EN 10305-1:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 1: Seamless cold drawn tubes |
ISO 8434-2:2007 | Metallic tube connections for fluid power and general use — Part 2: 37 degree flared connectors |
ISO 1179-4:2007 | Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 4: Stud ends for general use only with metal-to-metal sealing (type B) |
EN 10305-4:2016 | Steel tubes for precision applications - Technical delivery conditions - Part 4: Seamless cold drawn tubes for hydraulic and pneumatic power systems |
ISO 6149-3:2006 | Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 3: Dimensions, design, test methods and requirements for light-duty (L series) stud ends |
EN 1092-4:2002 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 4: Aluminium alloy flanges |
ISO 23936-2:2011 | Petroleum, petrochemical and natural gas industries — Non-metallic materials in contact with media related to oil and gas production — Part 2: Elastomers |
ISO 8434-3:2005 | Metallic tube connections for fluid power and general use — Part 3: O-ring face seal connectors |
ISO 23551-1:2012 | Safety and control devices for gas burners and gas-burning appliances Particular requirements Part 1: Automatic and semi-automatic valves |
ISO 8434-6:2009 | Metallic tube connections for fluid power and general use — Part 6: 60 degree cone connectors with or without O-ring |
SAE J 514 : 2012 | HYDRAULIC TUBE FITTINGS |
EN 10241:2000 | Steel threaded pipe fittings |
ISO 6149-1:2006 | Connections for hydraulic fluid power and general use Ports and stud ends with ISO 261 metric threads and O-ring sealing Part 1: Ports with truncated housing for O-ring seal |
EN 10284:2000 | Malleable cast iron fittings with compression ends for polyethylene (PE) piping systems |
IEC 60534-2-3:2015 | Industrial-process control valves - Part 2-3: Flow capacity - Test procedures |
EN 12760:2016 | Industrial valves - Socket welding ends for steel valves |
ISO 1179-2:2013 | Connections for general use and fluid power — Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing — Part 2: Heavy-duty (S series) and light-duty (L series) stud ends with elastomeric sealing (type E) |
EN 10242:1994/A2:2003 | THREADED PIPE FITTING IN MALLEABLE CAST IRON |
EN 1092-2:1997 | Flanges and their joints - Circular flanges for pipes, valves, fittings and accessories, PN designated - Part 2: Cast iron flanges |
EN 10226-1:2004 | Pipe threads where pressure tight joints are made on the threads - Part 1: Taper external threads and parallel internal threads - Dimensions, tolerances and designation |
SAE J512 : 1997 | AUTOMOTIVE TUBE FITTINGS |
IEC 60534-1:2005 | Industrial-process control valves - Part 1: Control valve terminology and general considerations |
ISO 228-1:2000 | Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation |
ISO 23550:2011 | Safety and control devices for gas burners and gas-burning appliances General requirements |
ISO 1179-3:2007 | Connections for general use and fluid power Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 3: Light-duty (L series) stud ends with sealing by O-ring with retaining ring (types G and H) |
IEC 60730-1:2013+AMD1:2015 CSV | Automatic electrical controls - Part 1: General requirements |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.