I.S. EN 12516-1:2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
INDUSTRIAL VALVES - SHELL DESIGN STRENGTH - PART 1: TABULATION METHOD FOR STEEL VALVE SHELLS
Hardcopy , PDF
21-01-2020
26-11-2014
For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
Only cited Standards give presumption of conformance to New Approach Directives/Regulations.
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and units
5 Material groups and material temperature limitations
6 Pressure/temperature (p/t) ratings
7 Temperature effects
8 Dimensions
9 Auxiliary connections
10 End dimensions
11 Marking
Annex A (normative) Methods used for establishing pressure/temperature ratings
Annex B (normative) Material groups
Annex C (informative) Special Class
Annex D (informative) Radiographic procedure and acceptance standards
Annex E (informative) Magnetic particle examination procedure and acceptance standards
Annex F (informative) Liquid penetrant examination procedure and acceptance standards
Annex G (informative) Ultrasonic examination procedure and acceptance standards
Annex H (informative) Requirement for Limited Class valves in sizes DN 65 and smaller
Annex I (informative) ASTM/ASME material
Annex J (informative) Relationship between DN, NPS, pipe inside diameter Dni, pipe outside diameter OD
Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC (Pressure Equipment Directive)
Bibliography
This European Standard specifies the tabulation method for determining the wall thickness of valve bodies, bonnets and covers with essentially circular cross-section made in forged, cast or fabricated steel.
Committee |
TC 69
|
DocumentType |
Standard
|
Pages |
206
|
ProductNote |
NOTE: The date of any NSAI previous adoption may not match the date of its original CEN/CENELEC document. THIS STANDARD ALSO REFERS TO EN 10213:2007,ASME Section II
|
PublisherName |
National Standards Authority of Ireland
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
Standards | Relationship |
UNI EN 12516-1 : 2014 | Identical |
DIN EN 12516-1:2015-01 | Identical |
NBN EN 12516-1 : 2014 | Identical |
NEN EN 12516-1 : 2014 | Identical |
NF EN 12516-1 : 2014 | Identical |
BS EN 12516-1 : 2014 | Identical |
EN 12516-1:2014 | Identical |
ONORM EN 12516-1 : 2014 | Identical |
UNE-EN 12516-1:2016 | Identical |
NS EN 12516-1 : 2014 | Identical |
SN EN 12516-1 : 2015 | Identical |
EN ISO 9692-1:2013 | Welding and allied processes - Types of joint preparation - Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels (ISO 9692-1:2013) |
EN 10228-3:1998 | Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings |
ASTM E 446 : 2015 : REDLINE | Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness |
EN 10028-7:2000 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
ASTM E 186 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (2 to 4<fraction><num>1</num><den>2</den></fraction > in. (50.8 to 114 mm)) Steel Castings |
EN 10222-2:1999 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperature properties |
EN 10213:2007+A1:2016 | Steel castings for pressure purposes |
ASTM E 446 : 2014 | Standard Reference Radiographs for Steel Castings Up to 2 in. (50.8 mm) in Thickness |
EN 10028-3:2017 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
EN 19:2002 | Industrial valves - Marking of metallic valves |
ASTM E 280 : 2010 | Standard Reference Radiographs for Heavy-Walled (4<span class='unicode'>½</span> to 12-in. (114 to 305-mm)) Steel Castings |
EN 1759-1:2004 | Flanges and their joint - Circular flanges for pipes, valves, fittings and accessories, Class designated - Part 1: Steel flanges, NPS 1/2 to 24 |
EN 12680-1:2003 | Founding - Ultrasonic examination - Part 1: Steel castings for general purposes |
EN 10222-3:1998 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
EN 12516-4:2014 | Industrial valves - Shell design strength - Part 4: Calculation method for valve shells manufactured in metallic materials other than steel |
EN 10025-1:2004 | Hot rolled products of structural steels - Part 1: General technical delivery conditions |
EN 736-2:2016 | Valves - Terminology - Part 2: Definition of components of valves |
ISO 5579:2013 | Non-destructive testing — Radiographic testing of metallic materials using film and X- or gamma rays — Basic rules |
EN 10028-2:2017 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
EN 10228-1:1999 | Non-destructive testing of steel forgings - Part 1: Magnetic particle inspection |
EN 10028-7:2016 | Flat products made of steels for pressure purposes - Part 7: Stainless steels |
EN ISO 9934-1:2016 | Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2016) |
ISO 9692-1:2013 | Welding and allied processes — Types of joint preparation — Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels |
ISO 15614-1:2017 | Specification and qualification of welding procedures for metallic materials — Welding procedure test — Part 1: Arc and gas welding of steels and arc welding of nickel and nickel alloys |
EN 10028-3:2003 | Flat products made of steels for pressure purposes - Part 3: Weldable fine grain steels, normalized |
EN 10028-2:2003 | Flat products made of steels for pressure purposes - Part 2: Non-alloy and alloy steels with specified elevated temperature properties |
EN ISO 5579:2013 | Non-destructive testing - Radiographic testing of metallic materials using film and X- or gamma rays - Basic rules (ISO 5579:2013) |
EN 10222-3:2017 | Steel forgings for pressure purposes - Part 3: Nickel steels with specified low temperature properties |
EN 10222-5:2017 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
EN 10228-3:2016 | Non-destructive testing of steel forgings - Part 3: Ultrasonic testing of ferritic or martensitic steel forgings |
EN 736-2:1997 | Valves - Terminology - Part 2: Definition of components of valves |
EN 10028-4:2003 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
EN 12516-3:2002/AC:2003 | VALVES - SHELL DESIGN STRENGTH - PART 3: EXPERIMENTAL METHOD |
ISO 4200:1991 | Plain end steel tubes, welded and seamless — General tables of dimensions and masses per unit length |
EN 10222-4:2017 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
ISO 9934-1:2016 | Non-destructive testing — Magnetic particle testing — Part 1: General principles |
EN 10222-2:2017 | Steel forgings for pressure purposes - Part 2: Ferritic and martensitic steels with specified elevated temperatures properties |
EN 1369:2012 | Founding - Magnetic particle testing |
EN 462-1:1994 | Non-destructive testing - Image quality of radiographs - Part 1: Image quality indicators (wire type) - Determination of image quality value |
ASTM E 280 : 2015 : REDLINE | Standard Reference Radiographs for Heavy-Walled (4<fraction><num>1</num><den>2</den></fraction > to 12 in. (114 to 305 mm)) Steel Castings |
EN 12681 : 2003 | FOUNDING - RADIOGRAPHIC EXAMINATION |
ASTM E 186 : 2010 | Standard Reference Radiographs for Heavy-Walled (2 to 4<span class='unicode'>½</span>-in. (50.8 to 114-mm)) Steel Castings |
ISO 7005-1:2011 | Pipe flanges — Part 1: Steel flanges for industrial and general service piping systems |
EN 12516-2:2014 | Industrial valves - Shell design strength - Part 2: Calculation method for steel valve shells |
EN 10222-5:1999 | Steel forgings for pressure purposes - Part 5: Martensitic, austenitic and austenitic-ferritic stainless steels |
EN 571-1:1997 | Non destructive testing - Penetrant testing - Part 1: General principles |
EN 10028-4:2017 | Flat products made of steels for pressure purposes - Part 4: Nickel alloy steels with specified low temperature properties |
EN 19:2016 | Industrial valves - Marking of metallic valves |
EN 10222-4:1998 | Steel forgings for pressure purposes - Part 4: Weldable fine grain steels with high proof strength |
EN 736-3:2008 | Valves - Terminology - Part 3: Definition of terms |
EN ISO 9934-1:2001 | Non-destructive testing - Magnetic particle testing - Part 1: General principles (ISO 9934-1:2001) |
EN 287-1:2011 | Qualification test of welders - Fusion welding - Part 1: Steels |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.