CSA A23.1 A23.2 : 2014
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
CONCRETE MATERIALS AND METHODS OF CONCRETE CONSTRUCTION/TEST METHODS AND STANDARD PRACTICES FOR CONCRETE
Hardcopy , PDF
24-07-2019
English, French
02-08-2018
Preface
A23.1-14, Concrete materials and methods of concrete construction
0 Introduction
1 Scope
2 Reference publications
3 Definitions
4 Materials and concrete properties
5 Production and delivery
6 Formwork, reinforcement, and prestressing
7 Placing, finishing, and curing concrete
8 Concrete with special performance or material requirements
9 Concrete for housing and small buildings (R class concrete)
Annexes
A (informative) - Special cements
B (informative) - Alkali-aggregate reaction
C (informative) - Tolerances: Principles, preferred sizes, and usage
D (informative) - Guidelines for curing and protection
E (informative) - Concrete surface tolerances: Elevation, slope, and
waviness
F (informative) - Abrasion resistance of concrete surfaces
G (informative) - Sample grouting record
H (informative) - Fibre-reinforced concrete
I (informative) - High-performance concrete
J (informative) - Guide for selecting alternatives when ordering
concrete using Table
K (informative) - Concrete made with high-volume supplementary
cementing materials
L (informative) - Mineral filler as an aggregate for concrete
M (informative) - Sustainable development, construction, and
concrete
N (informative) - Requirements for pervious concrete
O (informative) - Aggregate made from recycled concrete for use
in hydraulic cement concrete
P (informative) - Impact of sulphides in concrete aggregate on
concrete behaviour
Q (informative) - Simple method to optimize combined aggregate
gradation
R (informative) - Residential Concrete Construction
A23.2-14, Test methods and standard practices for concrete
1 Scope
2 Reference publications
3 Definitions
4 Reporting
Test Methods and standard practices
A23.2-1A - Sampling aggregates for use in concrete
A23.2-2A - Sieve analysis of fine and coarse aggregate
A23.2-3A - Clay lumps in natural aggregate
A23.2-4A - Low-density granular material in aggregate
A23.2-5A - Amount of material finer than 80 [mu]m in aggregate
A23.2-6A - Relative density and absorption of fine aggregate
A23.2-7A - Test for organic impurities in fine aggregates for
concrete
A23.2-8A - Measuring mortar-strength properties of fine aggregate
A23.2-9A - Soundness of fine and coarse aggregate by use of
magnesium sulphate
A23.2-10A - Bulk density of aggregate
A23.2-11A - Surface moisture in fine and coarse aggregate
A23.2-12A - Relative density and absorption of coarse aggregate
A23.2-13A - Flat and elongated particles in coarse aggregate
A23.2-14A - Potential expansivity of aggregates (procedure for
length change due to alkali-aggregate reaction in
concrete prisms at 38 degrees C)
A23.2-15A - Petrographic examination of aggregates
A23.2-16A - Resistance to degradation of small-size coarse
aggregate by abrasion and impact in the Los Angeles
machine
A23.2-17A - Resistance to degradation of large-size coarse
aggregate by abrasion and impact in the Los Angeles
machine
A23.2-23A - Test method for the resistance of fine aggregate
to degradation by abrasion in the Micro-Deval
apparatus
A23.2-24A - Test method for the resistance of unconfined
coarse aggregate to freezing and thawing
A23.2-25A - Test method for detection of alkali-silica reactive
aggregate by accelerated expansion of mortar bars
A23.2-26A - Determination of potential alkali-carbonate
reactivity of quarried carbonate rocks by chemical
composition
A23.2-27A - Standard practice to identify degree of
alkali-reactivity of aggregates and to identify
measures to avoid deleterious expansion in concrete
A23.2-28A - Standard Practice for laboratory testing to
demonstrate the effectiveness of supplementary
cementing materials and lithium-based admixtures
to prevent alkali-silica reaction in concrete
A23.2-29A - Test method for the resistance of coarse aggregate
to degradation by abrasion in the Micro-Deval
apparatus
A23.2-1B - Testing for properties of flowable grout
A23.2-2B - Determination of sulphate ion content in groundwater
A23.2-3B - Determination of total or water-soluble sulphate ion
content of soil
A23.2-4B - Sampling and determination of water-soluble chloride
ion content in hardened grout or concrete
A23.2-6B - Determination of bond strength of bonded toppings
and overlays and of direct tensile strength of concrete,
mortar, and grout
A23.2-7B - Random sampling of construction materials
A23.2-8B - Determination of water-soluble sulphate ion content
of recycled aggregates containing crushed concrete
A23.2-1C - Sampling plastic concrete
A23.2-2C - Making concrete mixes in the laboratory
A23.2-3C - Making and curing concrete compression and flexural
test specimens
A23.2-4C - Air content of plastic concrete by the pressure method
A23.2-5C - Slump of concrete
A23.2-6C - Density, and yield, of plastic concrete
A23.2-7C - Air content of plastic concrete by the volumetric method
A23.2-8C - Flexural strength of concrete (using simple beam with
third-point loading)
A23.2-9C - Compressive strength of cylindrical concrete specimens
A23.2-10C - Accelerating the curing of concrete cylinders and
determining their compressive strength
A23.2-11C - Water content, density, absorption, and voids in
hardened concrete, grout, or mortar
A23.2-12C - Making, curing, and testing compression test specimens
of no-slump concrete
A23.2-13C - Splitting tensile strength of cylindrical concrete
specimens
A23.2-14C - Obtaining and testing drilled cores for compressive
strength testing
A23.2-15C - Evaluation of concrete strength in place using the
pullout test
A23.2-16C - Determination of steel or synthetic fibre content in
plastic concrete
A23.2-17C - Temperature of freshly mixed hydraulic cement
concrete
A23.2-18C - Determination of total water content of normal
weight fresh concrete
A23.2-19C - Slump flow of concrete
A23.2-20C - Passing ability of self-consolidating concrete by
J-ring and slump cone
A23.2-21C - Test Method for length change of hardened concrete
A23.2-22C - Scaling resistance of concrete surfaces exposed to
deicing chemicals using mass loss
A23.2-23C - Electrical indication of concrete's ability to resist
chloride ion penetration
A23.2-1D - Moulds for forming vertical concrete test cylinders
Annexes
A (informative) - Nondestructive methods for testing concrete
B (informative) - Form for reporting compressive strength of
concrete test cylinders
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.